Copper recovery by cementing from waste solutions derived from the manufacturing/printing industry | ||
| dc.conicet.organizacion | Consejo Nacional de Investigaciones Científicas y Técnicas. Oficina de Coordinación Administrativa Ciudad Universitaria. Instituto de Química, Física de los Materiales, Medioambiente y Energía. Universidad de Buenos Aires. Facultad de Ciencias Exactas y Naturales. Instituto de Química, Física de los Materiales, Medioambiente y Energía | |
| dc.conicet.organizacion | Universidad de Buenos Aires. Facultad de Ingeniería. Departamento de Física. Grupo de Medios Porosos | |
| dc.conicet.organizacion | Universidad de Buenos Aires. Facultad de Ingeniería. Departamento de Física. Grupo de Medios Porosos | |
| dc.conicet.organizacion | Consejo Nacional de Investigaciones Científicas y Técnicas | |
| dc.conicet.organizacion | Consejo Nacional de Investigaciones Científicas y Técnicas. Oficina de Coordinación Administrativa Ciudad Universitaria. Instituto de Química, Física de los Materiales, Medioambiente y Energía. Universidad de Buenos Aires. Facultad de Ciencias Exactas y Naturales. Instituto de Química, Física de los Materiales, Medioambiente y Energía | |
| dc.contributor.author | Costa, Cecilia Daniela | |
| dc.contributor.author | Lustig, Sonia | |
| dc.contributor.author | D'angelo, María Verónica | |
| dc.contributor.author | González, Graciela Alicia | |
| dc.date.issued | 2020-04 | |
| dc.description.abstract | We report the optimal conditions for copper recovery on a laboratory scale through a cementation process from industrial waste solutions. As cementing agent, aluminum was employed from different sources: discarding aluminum from soda cans and turning chip and commercial meshes. The percentage of recovery is highly dependent on the exposed area of aluminum and chloride additions. It was determined that the optimal chloride concentration should be equal to or greater than 100 mM and the ratio between mass of aluminum and volume of copper solution must be greater than (42+/-4) mg/mL for mesh or shavings to obtain recoveries up to 90 %. For the case of aluminum from soda cans, this relation or the treatment time should be increased to reach the same relevant recoveries. As revealed by Scanning Electron Microscopy and X-Ray Diffraction experiments, the obtained copper is polycrystalline and dendritic, with low percentage of oxidized compounds. Under the conditions tested, the source of aluminum used does not seem to affect the quality of the product obtained. The conditions studied allow to scale the procedure and thus achieve the recovery of a metal of high economic value and reduce the environmental impact of industries such as the manufacture of printed circuits. | es |
| dc.description.fil | Fil: Costa, Cecilia Daniela. Consejo Nacional de Investigaciones Científicas y Técnicas. Oficina de Coordinación Administrativa Ciudad Universitaria. Instituto de Química, Física de los Materiales, Medioambiente y Energía. Universidad de Buenos Aires. Facultad de Ciencias Exactas y Naturales. Instituto de Química, Física de los Materiales, Medioambiente y Energía; Argentina | |
| dc.description.fil | Fil: Lustig, Sonia. Universidad de Buenos Aires. Facultad de Ingeniería. Departamento de Física. Grupo de Medios Porosos; Argentina | |
| dc.description.fil | Fil: D'angelo, María Verónica. Universidad de Buenos Aires. Facultad de Ingeniería. Departamento de Física. Grupo de Medios Porosos; Argentina. Consejo Nacional de Investigaciones Científicas y Técnicas; Argentina | |
| dc.description.fil | Fil: González, Graciela Alicia. Consejo Nacional de Investigaciones Científicas y Técnicas. Oficina de Coordinación Administrativa Ciudad Universitaria. Instituto de Química, Física de los Materiales, Medioambiente y Energía. Universidad de Buenos Aires. Facultad de Ciencias Exactas y Naturales. Instituto de Química, Física de los Materiales, Medioambiente y Energía; Argentina | |
| dc.format | application/pdf | es |
| dc.identifier.citation | Costa, Cecilia Daniela; Lustig, Sonia; D'angelo, María Verónica; González, Graciela Alicia; Copper recovery by cementing from waste solutions derived from the manufacturing/printing industry; Elsevier; Journal of Environmental Chemical Engineering; 8; 4; 4-2020; 1-19 | es |
| dc.identifier.institucional | CONICET | |
| dc.identifier.issn | 2213-3437 | es |
| dc.identifier.repo | CONICET Digital | |
| dc.identifier.uri | http://hdl.handle.net/11336/142958 | |
| dc.journal.number | 4 | es |
| dc.journal.pagination | 1-19 | es |
| dc.journal.pais | Países Bajos | es |
| dc.journal.title | Journal of Environmental Chemical Engineering | es |
| dc.journal.volume | 8 | es |
| dc.language.iso | eng | es |
| dc.publisher | Elsevier | es |
| dc.relation.alternativeid | info:eu-repo/semantics/altIdentifier/url/https://linkinghub.elsevier.com/retrieve/pii/S2213343720303377 | |
| dc.relation.alternativeid | info:eu-repo/semantics/altIdentifier/doi/http://dx.doi.org/10.1016/j.jece.2020.103989 | |
| dc.rights | info:eu-repo/semantics/openAccess | * |
| dc.rights.uri | https://creativecommons.org/licenses/by-nc-sa/2.5/ar/ | * |
| dc.subject | CEMENTATION | es |
| dc.subject | COPPER RECOVERY | es |
| dc.subject | DISCARDING ALUMINUM | es |
| dc.subject | ELECTROPLATING SOLUTIONS | es |
| dc.subject | ETCHING SOLUTIONS | es |
| dc.subject | X-RAY DIFFRACTION | es |
| dc.subject.classification | Otras Ingeniería Química | es |
| dc.subject.classification | Ingeniería Química | es |
| dc.subject.classification | INGENIERÍAS Y TECNOLOGÍAS | es |
| dc.title | Copper recovery by cementing from waste solutions derived from the manufacturing/printing industry | es |
| dc.type | info:eu-repo/semantics/article | |
| dc.type | info:ar-repo/semantics/artículo | |
| dc.type | info:eu-repo/semantics/publishedVersion | |
Archivos
Bloque original
Cargando...
- Nombre:
- CONICET_Digital_Nro.f76d7be1-a267-4ca2-a267-03206f703fa8_A.pdf
- Tamaño:
- 1.95 MB
- Formato:
- Adobe Portable Document Format