Determination and Analysis of Residual Stresses Induced by High Speed Milling Using a Micro-indent Method | ||
| dc.conicet.fuente | individual | |
| dc.conicet.organizacion | Universidad Tecnológica Nacional. Facultad Regional Rafaela | |
| dc.conicet.organizacion | Universidad Tecnológica Nacional. Facultad Regional Rafaela | |
| dc.conicet.organizacion | Universidad Tecnológica Nacional. Facultad Regional Rafaela | |
| dc.conicet.organizacion | Instituto Nacional de Tecnología Industrial | |
| dc.conicet.paisOrganizacion | Argentina | |
| dc.conicet.paisOrganizacion | Argentina | |
| dc.conicet.paisOrganizacion | Argentina | |
| dc.conicet.paisOrganizacion | Argentina | |
| dc.conicet.produccionid | 8064040 | |
| dc.contributor.author | Vottero, S. | |
| dc.contributor.author | Diaz, Felipe Victor | |
| dc.contributor.author | Mammana, Claudio Alejandro | |
| dc.contributor.author | Guidobono, A. | |
| dc.date.accessioned | 2019-11-24T23:48:38Z | |
| dc.date.available | 2019-11-24T23:48:38Z | |
| dc.date.issued | 2018-06 | |
| dc.date.updated | 2019-09-27T15:01:35Z | |
| dc.description.abstract | The purpose of this work is to determine and analyze residual stress normal components and anisotropy degrees introduced by high-speed milling in specimens of AA 6082-T6 and AA 7075-T6 aluminum alloys. At each machined sample, the climb and conventional cutting zones were evaluated and compared. This paper includes a comprehensive study of thermal and mechanical effects associated with the residual stress introduction. For normal components determination, an optimized micro-indent method was used. Each measurement sequence from this approach was performed using a high accuracy measuring machine and classified according to thermal deviations measured. The residual displacements were determined with an absolute error down to ±300 nm. The normal components analysis allowed to infer the strong influence of the rolling process previous to high-speed milling and besides, the stress levels associated with thermal effects (higher in AA 7075-T6). Finally, the lower residual stress anisotropy degrees in both materials observed in the conventional cutting zone would indicate more homogenous local plastic stretching in this region for all planar directions. | es |
| dc.description.fil | Fil: Vottero, S.. Universidad Tecnológica Nacional. Facultad Regional Rafaela; Argentina | |
| dc.description.fil | Fil: Diaz, Felipe Victor. Universidad Tecnológica Nacional. Facultad Regional Rafaela; Argentina | |
| dc.description.fil | Fil: Mammana, Claudio Alejandro. Universidad Tecnológica Nacional. Facultad Regional Rafaela; Argentina | |
| dc.description.fil | Fil: Guidobono, A.. Instituto Nacional de Tecnología Industrial; Argentina | |
| dc.format | application/pdf | es |
| dc.identifier.citation | Vottero, S.; Diaz, Felipe Victor; Mammana, Claudio Alejandro; Guidobono, A.; Determination and Analysis of Residual Stresses Induced by High Speed Milling Using a Micro-indent Method; Maxwell Science Publication; Research Journal of Applied Sciences, Engineering and Technology; 15; 6; 6-2018; 236-241 | es |
| dc.identifier.institucional | CONICET | |
| dc.identifier.issn | 2040-7459 | es |
| dc.identifier.repo | CONICET Digital | |
| dc.identifier.uri | http://hdl.handle.net/11336/89632 | |
| dc.journal.number | 6 | es |
| dc.journal.pagination | 236-241 | es |
| dc.journal.pais | Estados Unidos | es |
| dc.journal.title | Research Journal of Applied Sciences, Engineering and Technology | es |
| dc.journal.volume | 15 | es |
| dc.language.iso | eng | es |
| dc.publisher | Maxwell Science Publication | es |
| dc.relation.alternativeid | info:eu-repo/semantics/altIdentifier/doi/http://dx.doi.org/10.19026/rjaset.15.5863 | |
| dc.rights | info:eu-repo/semantics/openAccess | * |
| dc.rights.uri | https://creativecommons.org/licenses/by-nc-sa/2.5/ar/ | * |
| dc.subject | ALUMINUM ALLOYS | es |
| dc.subject | ANISOTROPY | es |
| dc.subject | HIGH-SPEED MILLING | es |
| dc.subject | MICRO-INDENT METHOD | es |
| dc.subject | RESIDUAL STRESSES | es |
| dc.subject.classification | Mecánica Aplicada | es |
| dc.subject.classification | Ingeniería Mecánica | es |
| dc.subject.classification | INGENIERÍAS Y TECNOLOGÍAS | es |
| dc.title | Determination and Analysis of Residual Stresses Induced by High Speed Milling Using a Micro-indent Method | es |
| dc.type | info:eu-repo/semantics/article | |
| dc.type | info:ar-repo/semantics/artículo | |
| dc.type | info:eu-repo/semantics/publishedVersion | |
Archivos
Bloque original
Cargando...
- Nombre:
- CONICET_Digital_Nro.f5dcf032-d073-497c-8a41-66022ef1b7c6_A.pdf
- Tamaño:
- 237.37 KB
- Formato:
- Adobe Portable Document Format