Mostrar el registro sencillo del ítem
dc.contributor.author
Tognana, Sebastian Alberto
dc.contributor.author
Montecinos Espinoza, Susana de Los Angeles
dc.contributor.author
Gastien, Rosana
dc.contributor.author
Salgueiro, Walter Alberto
dc.date.available
2022-10-13T15:21:32Z
dc.date.issued
2021-07
dc.identifier.citation
Tognana, Sebastian Alberto; Montecinos Espinoza, Susana de Los Angeles; Gastien, Rosana; Salgueiro, Walter Alberto; Influence of fabrication parameters on the elastic modulus and characteristic stresses in 3D printed PLA samples produced via fused deposition modelling technique; De Gruyter; Journal Of Polymer Engineering; 41; 6; 7-2021; 490-498
dc.identifier.issn
0334-6447
dc.identifier.uri
http://hdl.handle.net/11336/173032
dc.description.abstract
Commonly used 3D printed samples are partially infilled to reduce time and cost of printing, with mechanical properties dependent on the infill. In this work, the influence of the percentage and pattern of infill in PLA printed samples on the elastic modulus and characteristic stresses was analyzed. The elastic modulus, E, and characteristic stresses (σ0.2, σ4 and the maximum tensile stress) were determined for each sample using impulse excitation technique, IET, and uniaxial tensile tests. An apparent density was calculated for each pattern and infill percentage, and the mechanical parameters were studied as a function of such density. The results of IET obtained in different modes of vibration were analyzed and an apparent value of E was calculated. FEM simulations were carried out and the results were compared with the experimental ones. The mechanical properties for different infill percentages and infill patterns were studied by comparing the specific values of E and the stresses. Samples with higher infill percentages exhibit the best specific values of maximum stress and E, but the sample with 20% infill has the highest specific yield stress and a good value of the specific E from flexural vibrations.
dc.format
application/pdf
dc.language.iso
eng
dc.publisher
De Gruyter
dc.rights
info:eu-repo/semantics/restrictedAccess
dc.rights.uri
https://creativecommons.org/licenses/by-nc-sa/2.5/ar/
dc.subject
3D PRINTING
dc.subject
CHARACTERISTIC STRESSES
dc.subject
ELASTIC MODULUS
dc.subject
IMPULSE EXCITATION TECHNIQUE
dc.subject
MECHANICAL TESTS
dc.subject.classification
Ingeniería de los Materiales
dc.subject.classification
Ingeniería de los Materiales
dc.subject.classification
INGENIERÍAS Y TECNOLOGÍAS
dc.subject.classification
Ingeniería Mecánica
dc.subject.classification
Ingeniería Mecánica
dc.subject.classification
INGENIERÍAS Y TECNOLOGÍAS
dc.title
Influence of fabrication parameters on the elastic modulus and characteristic stresses in 3D printed PLA samples produced via fused deposition modelling technique
dc.type
info:eu-repo/semantics/article
dc.type
info:ar-repo/semantics/artículo
dc.type
info:eu-repo/semantics/publishedVersion
dc.date.updated
2022-09-21T14:24:10Z
dc.journal.volume
41
dc.journal.number
6
dc.journal.pagination
490-498
dc.journal.pais
Alemania
dc.journal.ciudad
Berlin
dc.description.fil
Fil: Tognana, Sebastian Alberto. Universidad Nacional del Centro de la Provincia de Buenos Aires. Centro de Investigaciones en Física e Ingeniería del Centro de la Provincia de Buenos Aires. - Consejo Nacional de Investigaciones Científicas y Técnicas. Centro Científico Tecnológico Conicet - Tandil. Centro de Investigaciones en Física e Ingeniería del Centro de la Provincia de Buenos Aires. - Provincia de Buenos Aires. Gobernación. Comisión de Investigaciones Científicas. Centro de Investigaciones en Física e Ingeniería del Centro de la Provincia de Buenos Aires; Argentina
dc.description.fil
Fil: Montecinos Espinoza, Susana de Los Angeles. Universidad Nacional del Centro de la Provincia de Buenos Aires. Centro de Investigaciones en Física e Ingeniería del Centro de la Provincia de Buenos Aires. - Consejo Nacional de Investigaciones Científicas y Técnicas. Centro Científico Tecnológico Conicet - Tandil. Centro de Investigaciones en Física e Ingeniería del Centro de la Provincia de Buenos Aires. - Provincia de Buenos Aires. Gobernación. Comisión de Investigaciones Científicas. Centro de Investigaciones en Física e Ingeniería del Centro de la Provincia de Buenos Aires; Argentina
dc.description.fil
Fil: Gastien, Rosana. Ministerio de Defensa. Instituto de Investigaciones Científicas y Técnicas para la Defensa; Argentina
dc.description.fil
Fil: Salgueiro, Walter Alberto. Universidad Nacional del Centro de la Provincia de Buenos Aires. Centro de Investigaciones en Física e Ingeniería del Centro de la Provincia de Buenos Aires. - Consejo Nacional de Investigaciones Científicas y Técnicas. Centro Científico Tecnológico Conicet - Tandil. Centro de Investigaciones en Física e Ingeniería del Centro de la Provincia de Buenos Aires. - Provincia de Buenos Aires. Gobernación. Comisión de Investigaciones Científicas. Centro de Investigaciones en Física e Ingeniería del Centro de la Provincia de Buenos Aires; Argentina
dc.journal.title
Journal Of Polymer Engineering
dc.relation.alternativeid
info:eu-repo/semantics/altIdentifier/url/https://www.degruyter.com/document/doi/10.1515/polyeng-2021-0019/html
dc.relation.alternativeid
info:eu-repo/semantics/altIdentifier/doi/http://dx.doi.org/10.1515/polyeng-2021-0019
Archivos asociados